dipl/sections/vhdl_intro/vhdl_intro.tex

\documentclass[../../Diplomschrift.tex]{subfiles}
\begin{document}

\section{A short introduction to VHDL}
\label{app:vhdl-intro}

Designing a processor is a big task, and it's easiest to start very small. With software projects, this is usually in the form of a ``Hello World'' program - we will be designing a hardware equivalent of this.

\subsection{Prerequisites}

Other than a text editor, the following Free Software packages have to be installed:

\begin{savenotes}
\begin{description}
 \item[\icode{ghdl}\cite{ghdl}] to analyze, compile, and simulate the design
 \item[\icode{gtkwave}\cite{gtkwave}] to view the simulation waveform files
 \item[\icode{yosys}\cite{yosys}] to synthesize the design
 \item[\icode{ghdlsynth-beta}\cite{ghdlsynth-beta}] to synthesize the design
 \item[\icode{nextpnr-xilinx}\cite{nextpnr-xilinx}] to place and route the design 
 \item[\icode{Project X-Ray}\cite{prjxray}] for FPGA layout data and bitstream tools
 \item[\icode{openFPGALoader}\cite{open-fpga-loader}] to load the bitstream onto the FPGA 
\end{description}
\end{savenotes}

\subsection{Creating a design}

A simple starting design is an up/down counter. The following VHDL code describes the device:

\lstinputlisting[
    style=vhdlstyle,
    label={lst:counter},
    caption={Counter entity},
    title=\texttt{counter.vhd},
]{vhdl/counter.vhd}

In order to test this design, a test bench has to be created:

\lstinputlisting[
    style=vhdlstyle,
    label={lst:counter-tb},
    caption={Counter test bench entity},
    title=\texttt{counter_tb.vhd},
]{vhdl/counter_tb.vhd}

\subsection{Simulating a design}

\begin{lstlisting}[
    style=terminal,
    label={lst:counter-sim-commands},
    caption={Commands required to simulate the counter design}]
# analyze the design files
ghdl -a --std=08 *.vhd
# elaborate the test bench entity
ghdl -e --std=08 counter_tb
# run the test bench, saving the signal trace to a GHW file
ghdl -r --std=08 counter_tb --wave=counter_tb.ghw
# open the trace with gtkwave (using the view configuration in counter_tb.gtkw)
gtkwave counter_tb.ghw counter_tb.gtkw
\end{lstlisting}

\begin{figure}
\includegraphics[width=\textwidth]{counter_gtkwave.png}
\caption{Screenshot of the counter test bench waveform in GTKWave}
\end{figure}

\subsection{Synthesizing a design}

An additional Xilinx Design Constraints (XDC) file is required to assign the signals to pins on the FPGA:

\lstinputlisting[
    label={lst:counter-constraints},
    caption={Counter design constraints file},
    title=\texttt{counter.xdc},
]{vhdl/counter.xdc}

\begin{lstlisting}[
    style=terminal,
    label={lst:counter-synth-commands},
    caption={Commands required to synthesize the counter design}]
# synthesize with yosys
yosys -m ghdl.so -p '
    ghdl --std=08 counter.vhd -e counter;
    synth_xilinx -flatten;
    write_json counter.json'
# place and route the design with nextpnr
nextpnr-xilinx --chipdb xc7a35tcsg324-1.bin --xdc counter.xdc --json counter.json --fasm counter.fasm
# convert the FPGA assembly to frames
fasm2frames.py --part xc7a35tcsg324-1 counter.fasm counter.frames
# convert the frames to a bitstream
xc7frames2bit --part-name xc7a35tcsg324-1 --frm-file counter.frames --output-file counter.bit
# upload the bitstream to the FPGA
openFPGALoader -b arty counter.bit
\end{lstlisting}

The current value of the counter is displayed in binary on the eight LEDs on the board. When switch 0 (enable) is in the high position, the counter can be advanced using button 0, with the direction set by switch 1. Button 1 resets the counter to zero.

\end{document}